PCB ISA 16-bit Backplane (Sergey Kiselev) Parts

Description

This sale is for the
PCB and parts for
16-bit ISA Backplane by Sergey Kiselev, check out his project at the URL below.
Please note:
This is the bare PCB and assembly will be required to finish the product. The full parts list is available below and from the designer's website below and this board has plenty of coverage on YouTube showing step by step assembly instructions.
This listing is for the following parts:
(select from drop down and add to cart each item you need)
PCB Main Board
1       PCB                  16-bit backplane
ISA Slots
8
BUS1 - BUS8
98 pin 16 - Bit
ISA
Slots set of 8
Connectors and Headers
1       ATX Connector
1
DE9M, right angle PCB mount
9 pin Serial port
4       3 x 1 pin header ( headers for jumper settings )
4       2 x 1 pin header ( headers for front panel)
1       5 x2 pin header (serial port header)
1       ATX connector (use pliers to make pins wider)
Resistors
2     10 kOhm, 1/4 W
2     1.5 kOhm, 1/4 W
2     1 kOhm, 1/4 W
5     470 Ohm, 1/4 W
2     470 Ohm, 16 pin DIP, isolated resistor array
1     50 kOhm Pot   (Not needed for the CD4511 decoder)
Capacitors
51     10 uf ceramic, 5.08 mm lead spacing
1       1 uf ceramic, 5.08 mm lead spacing
7       0.1 uf ceramic, 5.08 mm lead spacing
Diodes
2         1N4148    Diode
5         5 mm LED (Red, Green, Yellow, Blue, Orange)
1         2-digit 7 segment display (Common Cathode)
Integrated Circuit Chips
2         Decoder CD4511 (common cathode)
1         74LS688    8-bit magnitude comparator
1         74LS574    Octal D-Type Flip-Flop
1         74HCT74   D-Type flip-flop
1         74LS32      Quad 2-Input OR Gate
1         74HCT14   Hex inverting Schmitt trigger
1         7905 -5V voltage regulator
Sockets&Switches&Jumpers
3     14 pin 300 mil DIP socket
4     16 pin 300 mil DIP socket
2     20 pin 300 mil DIP socket
2     6mm Tactile Switch
4     Jumpers
I re-stock regularly if you don't find something for this board over here then please check back soon.
About the PC Board
This board allows you to build your own 8088 IBM XT/AT compatible computer and learn about computer architecture and design in the process. This ISA backplane is the base on which to build upon. The modular design allows maximum flexibility. Each of the 8 16 bit ISA slots accepts components such as CPU processor board, IO controller and graphics card. Mix and match different components.
ISA Backplane board was designed by Sergey Malinov
https://www.retrobrewcomputers.org/doku.php?id=boards:isa:isa-backplane:start
and is designed to be used together with the
Xi 8088 processor board
, but it can be used with other ISA SBC boards. In addition to eight parallelly connected ISA slots this backplane features an ATX power on/off circuit, a Port 80h POST display, a -5V regulator (most ATX power supplies don't supply -5V, but it can be required for some older ISA cards), serial port header, and a prototyping space.
Specifications
8 ISA Slots
Micro ATX compatible form factor
ATX power control circuit
regulator for -5V (needed for some sound blasters, modern power supplies don't produce it)
Port 80h POST diagnostic display
5 Power indicator LEDs (standby, 5V, -5V, 12V, -12V)
Serial DE9M header
Reset button and header
Avoid the hassle and the risk of parts from overseas, each component is tested to work with this board.
USPS First Class shipping will have this at your door in practically no time.